ASO-ABF100
Automatic Button Feeder
Choose Model
| Model | ABF100J | ABF100B |
|---|---|---|
| Apply For | Juki LK-1903A/ LK-1903AN Juki LK-1903B/ LK-1903BN | Brother 438FX |
| Rising Amount of Clamp | Maximum:13mm | |
| Feeding Time | 0.35~0.5 Sec. | |
| Button | Type: Circle Flat Button Size: Φ8~26mm ※Ø10mm is special specification, need to replace standard parts. |
|
| Button Hole | Standard: 2&4 Holes Option: 3 Holes | |
| Thickness of Button | 1.5~3.5mm | |
| Air Consumption | 20 L/min | |
| Air Pressure | 0.5 MPa | |
| Power Supply | single-phase AC 200~240V 50/60Hz | |
| Dimensions | 440(W)x560(D)x280(H)mm | |
Remark:
Standard: Professional table, All Set of Button Presser Foot ,Small/Big Button Serrarted Plate and Bottom Plate, 12 Sets of Standard Button Carrier.
Option: 3-Holed of Button Carrier,Button Spacer,Button Spacer with Laser Light.
Button sewing machine with auto button feeder enhances 300% efficiency of button sewing.
Cycle Time: 2.2 Sec./Button; 13,090 Buttons/8 Hr
BUTTON CARRIER MODULE
Modularized button carrier is for different button size and replacement.
PANEL
User friendly interface, all sewing parameters are clearly shown.
SENSOR SIGNAL DETECT
Checking the sensors detecting by A02 function of operation panel.
FLIP MECHANISM
Flip mechanism enhance the accuracy of ø16mm up button by auto air-blow.
SMART SENSOR OF BUTTON CLAMP
Button clamp can detect the button position and avoid sewing without button.
BUTTON CHANNEL ADJUSTMENT
Channel adjustment is controlled by stepping motor accurately .
DISCHARGING
Press the key and then remove all the buttons in the channel.
ELECTRONIC AUTOMATIC MEASUREMENT OF BUTTON SIZE
Accurate, Ultrafast, adjusting different button in a short time.
BUTTON CLAMP OF MACHINE HEAD
Button clamp is suitable for variety button size, the clamp can be used in different button size and no further adjustment needed.
SPECIFICATION OF BUTTON
| Codes of Parts | X＋0.05 －0.05 | D＋0.05 －0.05 | Button Holes |
| ABF118 | 2.2 | 1.0 | 4 |
| ABF119 | 2.2 | 1.0 | 2 |
| ABF120 | 2.4 | 1.2 | 4 |
| ABF121 | 2.4 | 1.2 | 2 |
| ABF122 | 2.8 | 1.2 | 4 |
| ABF123 | 2.8 | 1.2 | 2 |
| ABF124 | 3.2 | 1.2 | 4 |
| ABF125 | 3.2 | 1.2 | 2 |
| ABF126 | 3.6 | 1.2 | 4 |
| ABF127 | 3.6 | 1.2 | 2 |
| ABF269 | 2.6 | 1.2 | 4 |
| ABF270 | 2.6 | 1.2 | 2 |
BUTTON SHAPE
| Available Shape of Button |
 |
| Two sides must be have obvious differences to make sure that the machine can differentiate the front & reverse side of the buttons.The convex / concave must above 1.2mm height difference. |
| Unavailable Shape of Button |
 |
| The machine can’t identify the button when both sides are similar without obvious differences. |